0FB08-70514 Supersert Threaded Inserts

Avdel® Supersert® Structural Locking Nutsert Insert, Unit of Measure: Metric, 0.281 Inch Decimal Equivalent, 7.14mm Nominal Metric Diameter, Thread Size: M5x0.8 ISO-5H, 0.030 - 10.000 Inch (0.76 - 254.00mm) Grip Range, Low Profile Head, Body End: Open End, Steel Body Material, Material Detail: Low Carbon Steel BS 970 230 M07, Zinc Clear Trivalent Chromate Passivated Body Finish, Finish Detail: Zinc Clear Trivalent Chromate Passivated per ASTM B-633 Type I, Class 2, RoHS 3 Compliant Yes, 0.311 Inch (7.90mm) Head Diameter, 0.024 Inch (0.61mm) Head Height, Set Body Length: 0.213 Inch (5.40mm), Material Thickness Range: 0.031 Inch - Up (0.80mm - Up), Hole Size of Material Thickness 0.031 - 0.063 Inch (0.80 - 1.60mm): 0.281 Inch (7.14mm), Drill Size of Material Thickness 0.032 - 0.063 Inch (0.80 - 1.60mm): 9/32 Inch, Hole Size of Material Thickness 0.063 - 0.091 Inch (1.60 - 2.30mm): 0.287 Inch (7.30mm), Drill Size of Material Thickness 0.063 - 0.091 Inch (1.60 - 2.30mm): L, Hole Size of Material Thickness 0.091 - 0.126 Inch (2.30 - 3.20mm): 0.291 Inch (7.40mm), Drill Size of Material Thickness 0.091 - 0.126 Inch (2.30 - 3.20mm): M, Hole Size of Material Thickness 0.126 - 0.156 Inch (3.20 - 3.95mm): 0.295 Inch (7.50mm), Drill Size of Material Thickness 0.126 - 0.156 Inch (3.20 - 3.95mm): M, Hole Size of Material Thickness 0.156 - Up Inch (3.95 - Up): 0.295 Inch (7.50mm), Drill Size of Material Thickness 0.156 - Up Inch (3.95 - Up): M

- All fastener orders are supplied with Certificates of Conformance with packing lists. Additional Documentation such as material test reports may be available upon request (some at an additional charge). Please include your request in the "Order Note" section when submitting your order online. Click here for Quality Assurance & Compliance Documents.

The Supersert® threaded insert is a steel, low profile, plain bodied, expanding insert available in standard and metric thread sizes. An expanding insert is a single piece, which breaks into two pieces during installation. The lower threaded section of the insert draws up inside the upper sleeve section, causing the sleeve to expand 360o thus swaging the insert into the hole. Because the insert does not form a bubble on the backside of the application, an expanding insert can be used in blind hole applications. However, an expanding insert has less resistance to push out forces than a bubbling insert, which collapses into a bubble formation on the backside of the application. The low profile flange of the Supersert® insert results in near flush installation and clamp up making it ideal for flush fitting, thin sheet and low load bearing applications.

• Not grip sensitive
• Can be used in thick materials from 0.8mm (0.03 Inch), including blind holes
• Mechanical locking mechanism for applications requiring higher resistance to push out and pull out
• Access needed from only one side of the application, for high speed assembly
• Provide a female thread in application
• Can be installed in pre-coated or post painted applications without damaging the surface
• Low profile head allows near flush fit to application